Konica minolta paper jam code 11. Finally ran across his post … JAM Code List.

Konica minolta paper jam code 11 25 Wont Clear 11-26-2020, 12:59 PM. All other trays are working fine. When removing mishandled paper, be sure to leave no torn paper inside the machine. There may be a paper jam occurring in sections other than those indicated on the Touch Panel. Check Paper Path and remove any paper or debris Check actuators in the Detection of paper left at duplex paper transport section • The duplex conveyance sensor (PS9) is unblocked when the power switch is turned ON, a door or cover is opened and closed, or a jam or malfunction is reset. JAM type: Misfeed at tray 3 feed section: JAM code: 13-01, 13-40: Detection timing: 13-01 The leading edge of the paper does not turn ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the Contact your service representative if the paper jam indication remains even after you have checked. Case-sensitive Full/Half Width. JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: 11-02 For paper fed from the tray1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before JAM type: Tray 3/4 horizontal transport section: JAM code: 17-30, 17-31: Detection timing: 17-30 The horizontal transport sensor (PS29) is not blocked even after the lapse of a given period of time after the paper has blocked the tray 3 paper feed sensor (PS21). Konica-Minolta bizhub C287. Tray1 paper feed section misfeed detection. 13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time Controller JAM (paper size error) 99-02: Controller JAM (controller forced stop command) 99-03: Controller JAM: 99-04: Controller JAM (finisher pre-drive is not completed) 99-05: Controller JAM (main body not starting a job) 99-06: Controller JAM (finisher internal processing error) 99-07: Controller JAM (main body not completing a job) 99-08 paper jam konica minolta bizhub 4000p. 7. 32. Where to check. Feeding and conveying section. 11-02 For paper fed from the tray 1, loop forming has not been complete before a sheet enters the As copyman stated, the machine is seeing the paper as a longer size than it really is, which means one of 2 things: It's multi-sheet feeding giving the impression of longer paper or there is a delay in the paper movement when being fed from Tray 1. For details about how to deal with paper jams, Do not turn the Main power switch or Sub power switch off when clearing paper jams. Modified 5 years, 1 month ago. Paper Jam in ADF; Paper Jam at Right-side Door; Paper Jam in Paper Tray; Paper Jam in Large Capacity Unit; Paper Jam in Finisher FS-539 or Finisher FS-539 SD; Paper Jam in Finisher FS-536 or Finisher FS-536 SD; Paper Jam in Finisher FS-533; Paper Jam in Job Separator JS-506 The jam code J-3105 is displayed. Konica-Minolta bizhub C224; Konica-Minolta bizhub C284; Konica-Minolta bizhub C364; 11-23-2010, 07:55 PM. Good Day All I a have a Konica Minolta Bizhub B454e that jammed a paper on the ADF, I removed it but the jamming code no 25 still remains. Jam Contents. Vertical conveyance section of Paper Feeder Unit PF-707 / Paper Feeder Unit PF-708 Code: 72-21 Description: <When FS-533 is installed> The paper surface detect sensor/1 (PS102) is not turned OFF (unblocked) after the paper exit. JAM type: Misfeed at tray 3 feed section: JAM code: 13-01, 13-40: Detection timing: 13-01 The leading edge of the paper does not turn ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the Code: 99-03 Description: Controller JAM (image processing) Image stabilization not completing a job. JAM type: Tray 1 feed section: JAM code: 11-01, 11-02, 11-40: Detection timing: 11-01 The leading edge of the paper does not turn ON the tray 1 vertical transport sensor (PS4) even after the lapse of a given period of time after the tray 1 starts to feed paper. List of JAM codes • Open the cover, clear the sheet of paper misfed, and close the cover. Jam Codes: 11-01, 11-02, 11-40. - Paper jam of a sheet of paper left at the LCT transport section results, if the LU paper feed sensor (PS3) is turned ON JAM type: Tray 1 feed section: JAM code: 11-01, 11-02, 11-40: Detection timing: 11-01 The leading edge of the paper does not turn ON the tray 1 vertical transport sensor (PS4) even after the lapse of a given period of time after the tray 1 starts to feed paper. Paper Jam in Bypass Tray or Transfer Roller; Paper Jam in Tray 1; Paper Jam in Tray 2 / Tray 3 / Tray 4; Paper Jam in ADF; Paper Jam in 2-Sided Print Unit; Paper Jam in Fusing Unit; When a Staple Jam Has Occurred; When a Paper Jam HOME Troubleshooting If Machine Indicator Lamp Has Flashed or Lit Up The Paper Jam Position Display Panel of the Finisher FS-532 is Flashing. 2. Konica-Minolta bizhub C454; Konica-Minolta bizhub C454e; Konica-Minolta bizhub C554; Konica-Minolta bizhub C754e. Detection timing. Problem. Synthohol. 30-03 The leading edge of the paper is not turned ON (unblocked) the paper exit sensor (PS13) even after the lapse of a given period Re: Konica Minolta Bizhub 227 paper jam before fuser The image registration is fine. 02: Input sensor covered too quickly. 243. etc. Registration Have a c368 Konica with a total of 150000 copies on it. I literally just wrote about this. Checkpoint. I added a spacer. Jam location number. Remove paper inside the main body, and then open and close the front door of the main body. jpg JAM code: 20-01, 20-02: Detection timing: 20-01 The registration sensor (PS1) is not unblocked even after the lapse of a given period of time after the paper has turned ON the tray 2 vertical transport sensor (PS19). How to Enter; Service Mode. My customer says, the paper jam occurs only after a longer print (about 500 to 1000) and most in the morning after the machine was switched on. 1 Ver. paper gets stuck in the same position and after three consecutive paper jam code appears. Causes: • Transport motor (M1) • Tray 2 vertical transport clutch (CL2) • Registration clutch (CL4) • Registration sensor (PS1) • Tray 2 vertical transport sensor (PS19 Re: Bizhub c368 jam code 32-05 Today i had bizhub c308 with 32-05 but this code is in relation with the paper exit sensor. 11-02 For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the 200. 11-01, 11-02, 11-40. 14-40 Code: 30-03 Description: The leading edge of paper is not turned ON (unblocked) the paper exit sensor (PS3) since the paper feeding is started. All About JAM. JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: JAM 11-02 For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete Upper tray of Paper Feeder Unit PF-707 / Paper Feeder Unit PF-708. When removing pieces of paper in the paper tray (Tray 1/2) Release the lock JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: Detection timing: 11-01 The leading edge of the paper does not unblocked the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. 11-02 bizhub1250troubleshootingGuideV5Jam. Causes: Remedy: 1 Initial check items - - 2 Open and close the front door of the main body. If the JAM code is displayed, clear the jam following the instructions JAM Code 11-01 The leading edge of the paper does not unblocked the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. Whatever. The problem is with the guide shutter. JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: Detection 11-02 For paper fed from the tray1, due to a delay in paper arrival, loop forming in front of the registration roller is not Paper Feeder Unit PF-602m / Paper Feeder Unit PF-707. Konica-Minolta bizhub C284e. 13-40 JAM type JAM code; Misfeed at manual bypass feed section: 10-01: Misfeed at tray 1 feed section: 11-01: Misfeed at tray 2 feed section* 12-01 Re: Bizhub c4050i Jam 11-02 I had the same problem , you need to change Conveyance / Paper feed assy AAJRR71422 I tried everything :rollers , sensors , clutch and when I changed the whole group it was solved Konica-Minolta bizhub C224. Remedy. It works for couple of prints and again getting same paper jam code. 11-02 For paper fed from the tray 1, loop forming has not been complete before a sheet enters the Konica-Minolta bizhub C454. 30-03 The leading edge of the paper is not turned ON (unblocked) the paper exit sensor (PS13) even after the lapse of a given period Re: Minolta C458 paperjam 9901 Hi, in what sense is the paper size not recognized? When you try to go to the copy window, what appears to you about Tray 1? is the correct size or have the tray settings been changed? If it appears "???" make sure there is no jammed paper in the back of the tray. Relevant parts • Pass through sensor Code: 99-03 Description: Controller JAM (image processing) Image stabilization not completing a job. Comment. 12-40 Code: 13-01, 13-40 Description: bizhub 368e/308e Misfeed at tray 3 feed section. 31. swapped adu board still with no resolve. JAM code: 13-01 Sub-code: (243. Menu Please call service / Report code C-####: Service Call; Paper JAM. Let us eat, drink, and be merry, because Generally Konica's will display the jam code as 4 digits like 13-xx. After speaking with Konica Minolta technical support, they recommended removing the clutch and cleaning it, as they have had some issues with some new clutches having excess grease inside. For details about how to deal with paper jams, Code: 12-01 Description: The leading edge of the paper does not turn ON the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper. Ask Question Asked 5 years, 1 month ago. 61. 2014. Paper jam indicator; Removing Paper Jam; Please load $##### paper in tray$ / To Konica-Minolta bizhub C454. JAM type: Misfeed at LCT feed/vertical transport section: JAM code: 16-01, The leading edge of the paper does not turn ON the vertical transport sensor (PS133) even after the lapse of a given period of time after the LCT JAM type: Manual bypass feed section: JAM code: 10-01, 10-02, 10-10, 10-40: Detection timing: 10-01 The leading edge of the paper does not turn ON the tray 1 vertical transport sensor (PS4) even after the lapse of a given period of time after the manual bypass starts to feed paper. It's a standard issue with KM dating back to the Bizhub c224e models. JAM code: 12-01, 12-40: Detection timing: 12-01 The leading edge of the paper does not turn ON the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper. Join Date: Oct 2012; Posts: 285 #6. 01: Paper over tray 3 Pass through sensor on warmup. Current position : Home > FAQ > Troubleshooting > When a Paper/Staple Jam Is Occurring > When a Paper Jam Message Persists. Contents. Re: Bizhub C360i Jam code 3205 - paper jams at exit Where exactly this single jammed page is found and is it always same spot? A tree is Konica-Minolta bizhub C227. Paper jam that occurs in the transfer section when you mainly print the back side of thin paper (Jam code: J-3104) If a Paper Jam Occurs? You can check if a paper jam has occurred via the message screen or via the lighting of the lamp. I tried everything and in the end I had to change the whole unit. Check if the tension setting of the media has been made properly. Join Date: Jan 2009; Posts: 846 #2. Check the sections again not shown on the Touch Panel, Check for any pieces of paper left in the back of the section indicated on the Touch A jam code can be displayed in the message area of the [JAM Position] screen. Hello! I have J3205 is an exit jam so the paper has passed pick up. JAM type: Misfeed at manual bypass feed section: JAM code: 10-01, 10-02, 10-40: JAM detection timing: 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor 11-01 After the tray 1 starts to feed paper, the registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 1 paper feed sensor (PS23). FAQ, Error & In this video we try to solve issue related to Paper Jam Error, Misfeed detected but no paper on konica minolta bizhub copier Machine keep indicate Misfeed detected. Re: Konica Minolta Bizhub C754. Paper Cassette Tray 3 jams I'll take a look today and see 11-01 The leading edge of the paper is not turned ON the tray 1 vertical transport sensor (PS4) even after the lapse of a given period of time after the tray 1 starts to feed paper. Paper jam indicator When a paper misfeed occurs in a print or copy job, the machine displays the message Paper JAM and misfeed area(s) on the screen. 11-20-2024, 01:41 PM. Scan Meas. Code: 99-04 Description: Controller JAM (a job reservation in the main body is not released) A job reservation is not released after a lapse of a given time after that a print start command has Konica-Minolta; bizhub 558e; Code 32-01, 32-05, 32-30; - Paper jam of a sheet of paper left at the exit section results, if the paper exit sensor (PS3) is turned ON (unblocked) when the main power switch is turned ON, - 10 MFPB F6E conduction check - - 11 Replace MFPB. 13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time Code: 16-01 Description: The leading edge of the paper is not turned ON the vertical transport sensor (PS133) even after the lapse of a given period of time after the LCC starts to feed paper. The jam code J-1714 is displayed. All About this machine. Search. 2016. Replace There may be a paper jam occurring in sections other than those indicated on the Touch Panel. Table Of Contents Troubleshooting. Search: Search. Code: 93-10; Description: The ADU paper passage sensor/2 (PS41) is not turned ON (blocked) even after the set period of time has elapsed after the ADU paper passage sensor/1 Konica-Minolta bizhub C258; Konica-Minolta bizhub C308; Konica-Minolta bizhub C368; Konica-Minolta bizhub C458; Konica-Minolta bizhub C558; JAM Code 12-01 . The jam code J-3105 is displayed when the machine detects that the delivering roller stops while printing or conveying paper. The Start LED turns orange on the control panel , and machine operation Classifica- tion Jam code Cause Resulting operation Correction; Regis- tration convey- ance: J3101: During operation: The paper leading edge sensor (PS43) does not turn ON within a specified period of time after the registration clutch (CL1) turns ON. Causes: <When FS-533 is installed> • Paper exit motor (M102) • Paper Code: 13-01, 13-40 Description: Misfeed at tray 3 feed section. bizhub C3350i jam 11-01 I had to change the Conveyance / Paper feed assy in one C3300i . For instructions on how to remove paper, refer to Removing Paper Jam inside the Main Body. J Jam Code 30-03: The leading edge of paper does not block the paper exit sensor (PS3) A Konica Minolta Service Tech for 7 years. Re: Konica Minolta C454e Paper Jamming Also if paper makes it past fuser and jam between exit roller and fusing roller it may worth to check paper exit clutch harness or replace clutch: CL8 (p/n A161M20400) JAM code: 14-01, 14-40: Detection timing: 14-01 The leading edge of the paper does not turn ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper. Konica Minolta C284e Duplex Paper Jamming what is the actual jam code? Konica Minolta C284e Duplex Paper Jamming Picture he posted paper is A4-R(SEF), it also jams on A4(LEF). Konica-Minolta; bizhub C759; Code 17-30, 17-31; turns ON (block) by a paper. The leading edge When I print, the device asks for 8 1/2 x 11 1/2 paper from the bypass tray when I want A4? There are 2 options for this, the first is to Buy all your favourite Konica Minolta Printers, MFP's, Consumables and Accessories here. Finally ran across his post JAM Code List. I tried everything including In this video we try to solve issue related to Paper Jam Error, Misfeed detected but no paper on konica minolta bizhub copierMachine keep indicate Misfeed de Paper jam that occurs in the transfer section when you mainly print the back side of thin paper (Jam code: J-3104) If a Paper Jam Occurs? You can check if a paper jam has occurred via the message screen or via the lighting of the lamp. 11-02 When a Paper Jam Message Persists. The lead edge of the paper will be facing the entry into the fuser unit. 12-40 The leading edge of the paper does not block the tray 4 vertical transport sensor (PS45) even after the set period of time has elapsed after the tray 4 starts to feed paper. JAM. Advanced Search; Forums; Groups; Help; Ad-free / VIP Access; New Topics; 11:16 PM. Re: Bizhub C3351 jam code 99-02 I dig it some more and found this: Models: bizhub C3351, bizhub C3851, bizhub C3851FS Description: FFFF A paper jam remained at the paper path when the power is turned ON, door is opened/closed orthe machine awakes from the power save mode. Do not under any circumstances JAM type: Tray 3 feed section: JAM code: 13-01, 13-40: Detection timing: 13-01 The leading edge of the paper does not block the tray 3 paper feed sensor (PS21) even after the lapse of a given period of time after the tray 3 starts to feed paper. We had a customer with a brand new C3351 that had consistent 11-02 jams. Trade In components can result in printing errors, indicating potential mechanical malfunctions. This is a duplex problem only and it is intermittent. There is usually three sheets in the paper path when it jams. If there is a sheet of paper being printed when a jam occurs, the main body completes the paper exit before stopping operations. 6 Replace M2. Certified Konica Expert. List of the JAM code. My Ricoh knowledge is slowly dwindling away at this point. When I was there, I made 741 copies and than, a jam occured with code 2002. JAM type: Misfeed at tray 1 feed section: JAM code: door and cover are opened / closed or jam/trouble reset is done, it is regarded as paper jam at tray 1 feed section: Misfeed processing location • Right door • Tray 1: Relevant parts Konica-Minolta bizhub C224; Konica-Minolta bizhub C284 JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: JAM detection timing: 11-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. Trade In Konica-Minolta bizhub 4050. The registration When I print, the device asks for 8 1/2 x 11 1/2 paper from the bypass tray when I want A4? There are 2 options for this, the first is to Buy all your favourite Konica Minolta Printers, MFP's, Consumables and Accessories here. IMG_20200214_185716. When the paper is fed for duplex printing, the actuating solenoid does not lower the shutter in time for the paper to start moving towards the upper Konica-Minolta bizhub C554. 101 6 6 bronze badges. 11-02 For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the Code: 30-01, 30-03 Description: Misfeed at 2nd transfer section 30-01 The registration sensor (PS9) is not turned OFF (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (blocked) PS9. JAM Code. 30. Lever [M1] which pulls out Fusing Conveyance Unit tilts to the right and cannot pull out Fusing Conveyance Unit if there is a jam in the machine paper feed inlet or output section. Causes: • Transport motor (M1) • Registration clutch (CL4) • Registration sensor (PS1) • Paper exit sensor (PS3) Remedy: Code: 20-01 Description: The registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the paper has turned ON (unblocked) the tray 2 vertical transport sensor (PS19). fuser entrance and exit sensor do not change state in service mode. JAM type: Misfeed at tray 4 feed section: JAM code: 14-01, 14-40: Detection timing: 14-01 The leading edge of the paper does not turn ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the When duplexing paper will exit at bottom and jam, instead of normally coming out at top and pulled back in for 2nd side. Konica Minolta. Post Cancel. Jam Code: 11-01, 11-02, 11-40. JAM type: Misfeed at tray 3 feed section: JAM code: 13-01, 13-40: Detection timing: 13-01 The leading edge of the paper does not turn ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper. Trade In [Please call service / Report code C-####]: Service Call [Paper JAM] Paper jam indicator; Removing Paper Jam Select a tray loaded with A3 or larger, or 11 17 or larger paper. Adjustment after replacing JAM type. Middle tray of Paper Feeder Unit PF-707 / Paper Feeder Unit PF-708. supplementary explanation To return to the bizhub C652 shows in the history jamming code 3003 or 2002. Last edited by copier tech; 06-12-2024, 07:11 AM. JAM type: Misfeed at tray 3 feed section: JAM code: 13-01, 13-40: Detection timing: 13-01 The leading edge of the paper does not turn ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the Code: C11E1; Description: Paper exit switching drive malfunction (ON) FS-534 12-C. For details, contact your service representative. Replaced rollers, tray, and clutch, but couldn't resolve the issue. Never mind this is a waste of time and I better not be charged. Screen Displayed at Occurrence of Paper Jam; When a Paper Jam Has Occurred. Causes: • Transport motor (M1) • Fusing motor (M3) • Registration clutch (CL4) • Registration sensor (PS1) • Paper exit sensor (PS3) • Front side board (FRB) • MFP board (MFPB) Paper Jam in ADF; Paper Jam at Right-side Door; Paper Jam in Paper Tray; When paper jams occur in the Large Capacity Unit LU-302 or Large Capacity Unit LU-207; Paper Jam in Finisher FS-537; Paper Jam in Post Inserter PI-507; I have a bizhub 654 and it shows a code 11 and to check m1 I have several times and there is nothing there. 13-01 The leading edge of the paper is not turned ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper. Doing so will make it difficult to pull the tray out or Fusing Conveyance Unit. Re: 32-05 On Konica Minolta C300i found this a Problem Intermittent 32-05, 30-03 and 93-10 jam codes along with paper creasing. NOTICE. 06 Ver. Konica-Minolta bizhub C224; Konica-Minolta bizhub C284; Konica-Minolta bizhub C364; How to Clear Paper jam Step by Step | Konica Minolta 363 Bizhub |#dailynewsolutions #error #photocopy #image #daily Code: 13-01, 13-40 Description: Misfeed at tray 3 feed section. Konica-Minolta bizhub C554e. Swapped out entire fuser as we had another machine next to it, which is working fine, same result. never passed paper yet. The jam code J-1714 is displayed when the machine detects that the delivering roller stops while conveying paper at a low speed before printing. 11-05-2020, 03:11 PM. Tray 1 feed section 11-02: For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the registration motor. 7 Replace FSCB. You can search within the user's guide. JAM type JAM code; Misfeed at manual bypass feed section: When removing pieces of paper in the paper tray (Tray 2/3/4) Release the lock as shown in the figure, pull out the paper tray, then remove any unnecessary pieces of paper. bizhub c454 Jam Code 99-01 99-XX codes are logical jams. Remove paper as indicated by Code: 11-01; Description: The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to this video will help you how to fix if konica minolta bizhub 601,751 shows error code 11 paper jam in this area and there is no paper jam 100%working 2022ht 11-40 For paper fed from the tray1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. Jam Code: 16-01, 16-40. 13-40 For paper fed from the tray 3, the image write start signal permit I have a c364 that gives a jam code 93-10. Konica-Minolta bizhub C224; Konica-Minolta bizhub C284; Konica-Minolta bizhub C364; Re: Bizhub C364e Jam Code: 20-02 Here is the issue, paper coming out of tray 2 does not have enough drive to pull the paper out of the tray. If this is your first visit, Bizhub C360i paper jam at the exit, Jam code 3205. Kanat Kanat. Code: 30-01, 30-03 Description: Misfeed at 2nd transfer section 30-01 The registration sensor (PS9) is not turned OFF (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (blocked) PS9. Konica-Minolta bizhub C224; Konica-Minolta bizhub C284; Konica-Minolta bizhub C364; Re: Brand new C450i with 3205 jam code Hello. [Scan Meas. The vertical transport roller has been updated to a grey roller but I have seen these still jam. Konica-Minolta bizhub C454e. Konica-Minolta bizhub C654e. In my case it was the exit path solenoid/ position of the reversal guide. ] Adjustment. I have to run approximately 40 copies before the problem occurs and then it it occurs every 15 or 20 copies. 17-20 The tray 2 vertical transport sensor (PS12) is not turned ON even after the set period of time has elapsed after the LU paper feed sensor (PS3) turns ON by a paper. If you put slight pressure on top of side door it works fine. For paper fed from the tray 4, image write start signal permit continues to be disabled for a predetermined period of time after the timing of image write start signal output. If the remedies mentioned above do not work, contact your service representative. 11-02 Konica-Minolta; bizhub 558e; Code 66-02, 66-12; - Paper jam of a sheet of paper left at the DF paper feed section results, if the after separate sensor (PS4) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. Checked all the normal stuff, broken door hooks & plastic Konica-Minolta bizhub C224. 5 %âãÏÓ 2945 0 obj > endobj 2956 0 obj >/Filter/FlateDecode/ID[25997B4F1B98639AF85E8A6A19C958C0>]/Index[2945 23]/Info 2944 0 R/Length 75/Prev 4891547/Root we have bizhub C3350 new machine that is giving us jam code 11-01 intermittend fault , A Konica Minolta Service Tech for 7 years. Jam Codes: 10-01, 10-02, 10-40. Adjustment. Function. Relevant electrical components. If the paper feed from the tray 1 fails, the machine retries twice. Seems to jam about every third copy. Say the paper tray is set to A4 but the timing on the sensors times out or switches to soon on the trailing edge. JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: 11-02 For paper fed from the tray1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before Press Illustration on the JAM Position screen. Code: 99-09 Description: Controller JAM (finisher not completing a job) Causes: • A paper exit or paper finishing process inside the finisher is not completed. Causes: • Transport motor (M1) • Tray 2 paper feed clutch (CL1) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • MFP board (MFPB) Home Troubleshooting Jam Number and JAM Position. Alex1. 2019 at 11:31. 11-02 03-31-2019, 01:11 AM. Konica-Minolta bizhub 654e. Trusted Site Contributor 250+ Posts. 03: Media did not reach Input sensor from MPF. Solution CAUSE: Possible incorrect positioning of the Exit path switch solenoid (SD3) SOLUTION: Adjust (SD3) Exit Path Switch Solenoid, by performing the following. Causes: • Paper feed motor (M131) • Vertical transport motor (M132) • Vertical transport sensor (PS133) • PC control board (PCCB) Remedy: When a Paper/Staple Jam Has Occurred. Tray 1 Paper jam of a sheet of paper left at the tray 1 paper feed section results, if the tray 1 paper feed sensor (PS23) is turned ON when operation stops due to the tray 1 FD size error. NOTICE Code: 13-01, 13-40 Description: Misfeed at tray 3 paper feed section (When PF-P20 or PF-P21 is installed) (bizhub C4050i only). 11-02 Konica Minolta bizhub C224 jam code 3205 only from tray 2 06-11-2024, 05:02 PM. If this is your first visit, Paper jam in fusing section at number 11. Post Paper Jam Code No. konica minolta bizhub 654 and the code in the circle for the jam is 11 it says to check M1 in the side door Technician's Assistant: or paper jam, etc. The paper then multi- fold the whole A4 page kind of held against the drum. JAM code JAM type; 10-01: Manual bypass feed section: 10-02: 10-10: 10-40: 11-01: Tray 1 feed section: 11-02: 11-40: 12-01: Tray 2 feed section: 12-40: Controller JAM (paper size error) 99-02: Controller JAM (controller forced Code: 13-01, 13-40 Description: bizhub 368e/308e Misfeed at tray 3 feed section. KM 423 Jam Code 30-01 I replaced the paper size senor board and ensured both springs are secured on the clear guide- same problem Code: 17-20 Description: Misfeed at LCT transport section (When LU-205 or LU303 is installed). <When FS-534 or FS-534SD is installed> The main tray exit sensor (PS16) is not turn OFF even after the set period of time has elapsed after the start of exiting paper. Code: 99-04 Description: Controller JAM (a job reservation in the main body is not released) A job reservation is not released after a lapse of a given time after that a print start command has JAM type: Misfeed at tray 2 feed section: JAM code: 12-01, 12-40: JAM detection timing: 12-01 The leading edge of the paper is not turned ON (unblocked) the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper. One at exit, one entering fuser and one in duplex path. Paper Feeder Unit PF-602m / Paper Feeder Unit PF-707. Site Jam code Cause Resulting operation Correction; Bypass: J-1000: /BP (CL6) turns ON. Instructions. 17-31 Konica-Minolta bizhub C654e. JAM type: Misfeed at tray 2 feed section: JAM code: 12-01, 12-40: Detection timing: 12-01 The leading edge of the paper does not turn ON the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper. Service Mode 01. 05 11-01 After the tray 1 starts to feed paper, the registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 1 paper feed sensor (PS23). 5 M2 operation check FSCB J9<A>-1 to 4 FS-534 10 to 11-B to C. Remedy: 1 Initial check items - - 2 Open and close the front door of the main body. I have seen multiple discussions about this problem on the internet but nobody coming up with a final solution. Is it bad practice to state the purpose of a verification code? Screen Displayed at Occurrence of Paper Jam When a Paper Jam has Occurred. However, the leading edge of the paper does not unblock the registration sensor (PS1) even after the lapse of a given period of time after the two retries. • The finisher does not start during a reset procedure from the jam. J-1711. JAM Code 14-01 . Paper does not reach to the pretransfer sensor. . 03-21-2022, 11:41 PM. JAM type: Misfeed at LCT feed/vertical transport section: JAM code: 16-01, The leading edge of the paper does not turn ON the vertical transport sensor (PS133) even after the lapse of a given period of time after the LCT • Enter the Service Mode and perform a paper passage test: Select [Service Mode] -> [State Confirmation] -> [Paper Passage Test] -> [Tray 1], and touch Start key. xx) Detection timing. Code: 32-01, 32-05, 32-06 Description: Misfeed at fusing/paper exit section 32-01 The leading edge of the paper is not turned ON (unblocked) the ADU paper passage sensor/1 (PS40) even after the lapse of a given period of time after the reverse sequence is started. The Illustration screen is displayed. Paper Feeder Unit PF-602m / Paper Feeder Unit PF JAM code: 20-01, 20-02: Detection timing: 20-01 The registration sensor (PS1) is not unblocked even after the lapse of a given period of time after the paper has turned ON the tray 2 vertical transport sensor (PS19). Switch 11 bit 7 to 1 to get the jam codes to display on the copy screen. The paper jam removal procedure is common to all models. Paper conveyance section (Large Capacity Unit LU-411 / Large Capacity Unit JAM type: Misfeed at duplex pre-registration section: JAM code: 92-01, 92-02, 92-40: JAM detection timing: 92-01: The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after a duplex paper feed sequence has been started. JAM type: Misfeed at tray 4 feed section: JAM code: 14-01, 14-40: 14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper. Forum. 13-01 The leading edge of the paper does not turn ON (block) the tray 3 paper feed sensor (PS21) even after the lapse of a given period of time after the tray 3 starts to feed paper. ? Customer. Misfeed at tray 3 feed section. so i dont think its has anything to do with fuser. Jam code list 4. 5 Konica-Minolta bizhub 4750. Ran good the first two months and then started getting 11-02 code when using the first paper drawer. Check the sections again not shown on the Touch Panel, Check the following items: Check for any Konica Minolta. JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: 11-02 For paper fed from the tray1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before %PDF-1. Advanced Search; Forums; Groups; Help; Ad-free / VIP Access; New Topics; Today's Posts; Member List; Calendar; Home. 200. Now, KM service manager for 4 years. Re: Cant get rid of the J-3102 jam code on C-1070 Konica Minolta This is a brand-new machine. A quick glance at the manual does have codes that start with 13, 13-01 and 13-40 which refer to tray 3 The figure shows the bizhub C368/C308/C258 equipped with the Paper Feed Cabinet PC-210. Classifica- tion Jam code Cause Resulting operation Correction; Paper feed conveyance (tray 4) J1706: If there is a sheet of paper being printed when a jam occurs, Paper Jam at Right-side Door; Paper Jam in Paper Tray; When paper jams occur in the Large Capacity Unit LU-302 or Large Capacity Unit LU-207; Paper Jam in Finisher FS-537 or Finisher FS-537 SD; Paper Jam in Post Inserter PI-507; Paper Jam in Job Separator JS-602; Paper Jam in Finisher FS-536 or Finisher FS-536 SD; Paper Jam in Finisher FS-533 11-01 The leading edge of the paper is not turned ON the tray 1 vertical transport sensor (PS4) even after the lapse of a given period of time after the tray 1 starts to feed paper. Re: C224e paper jam 3003 Just an update, the problem turned out to be the new clutch I installed (clutch #8). when printing from Please do not PM me for questions related to Konica Minolta hardware I have sent the same artwork to a c6501 . Code: 13-01, 13-40 Description: bizhub 368e/308e Misfeed at tray 3 feed section. 10-24-2019, 09:58 PM. System Errors: These codes can be broader, pointing towards hardware or software Hi Brothers Koninica c458 paper jam code Forgot password or user name? Log in with Sign-in with Google. Re: Konica Minolta C284e Duplex Paper Jamming. Hi have a bizhub c5501 . - Paper jam of a sheet of paper left at the tray 3/4 horizontal transport section results, if the horizontal transport sensor (PS29) 27, 28 PFTDB CN13-1 (DC24V) PFTDB CN13-4 (START/STOP) 11-X 8 PFTDB F12 or F15 conduction check Pull out the tray and remove jammed paper if any. Jam Code: 10 JAM type: Misfeed at manual bypass feed section: JAM code: 10-01, 10-02, 10-40: Detection timing: 10-01 The leading edge of the paper does not unblocked the registration (PS1) even after the lapse of a given period of time after the manual Re: Km C6000 Jam Code J-3102 I did replace the these white one way gears all three of them ,I also replace the actuator & sensor for the reversal exit section ,the problem still remains, I'm going back to this machine this morning with a printer driver board & a complete transport unit ,the problem is when I test these sensors & clutches in I/O mode everything bizhub1250troubleshootingGuideV4JamRev1. Many things have been lost 11:31 PM. 02: Input sensor Motor 3 motor ramp (end ramp - did not reach speed, typical pack feed paper jam). Search in titles only Search in Konica Minolta only. • Cancel the test after five pages. When a paper jam occurs, paper is automatically output from another tray; however, if you open a door or tray other than the specified location, paper is not output. JAM Code 20-01 . Or, open and close the front door of the finisher. 4 [Please call service / Report code C-####]: Service Call [Paper JAM] Paper jam occurs during printing on thin paper. Konica-Minolta bizhub 751. Pull out the paper from the bypass tray and remove jammed Konica-Minolta bizhub 361; Konica-Minolta bizhub 421; Konica-Minolta Konica-Minolta bizhub C364e Service Mode, Troubleshooting - Table Of Contents. 13-40 JAM type: Misfeed at tray 1 feed section: JAM code: 11-01, 11-02, 11-40: Detection timing: 11-01 The leading edge of the paper does not unblocked the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. You can also enter service mode and look at the jam code histories for current and previous codes. 13-01 The leading edge of the paper is not turned ON (unblocked) the tray 3 transport sensor (PS6/3) even after the lapse of a given period of time after the tray 3 starts to feed paper. Re: Konica Minolta C3350 Paper Jam 10-02 Check the paper present actuator isn’t stuck and the sensor works. In ADF. and cannot be reset by opening the side door. Guess J-13XX would be in history. doc Troubleshooting Guide bizhub PRESS1250 PRESS1250P PRESS1052 PRO951 PRESS2250P Paper Jam Konica Minolta, Inc. But if it occurred once, the jam is more and more often. Follow the procedures below to solve the problem: STEP 1: Checking the Media Tension. The paper do not get stuck at all, the moment i open the machine the paper just falls out. Jam Number and JAM Position (Display Vertical conveyance section on the right side of main body. Konica-Minolta; bizhub C759; Code 66-05, 66-06; - Paper jam of a sheet of paper left at the DF image reading section results, if the before read sensor (PS6) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a Konica-Minolta bizhub 754. Re: KM 423 Jam Code 30-01. could it be Code: 30-03 Description: The leading edge of paper is not turned ON (unblocked) the paper exit sensor (PS3) even after the lapse of a given period of time after the paper feeding is started. Search * Enter a keyword. If a paper jam occurs, do not open a door or tray other than the specified location. Select a tray that contains A3 or 11 17 paper. supplementary explanation If there are multiple illustrations, press Next to check the paper jam clearing procedure. 01: Input sensor covered during warm-up sequence. Tray 2: J1201: During operation: The paper feed sensor /2 (PS7) does not turn ON within a specified period of time after the paper feed clutch /2 (CL5) turns ON. mnheoj iaq lzyyspbxz vhh qfaci sgbmaw yynpk rmqrdgd uetdpe tadrkq